Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
How to salvage unmentionable razors
#11
(03-18-2021, 01:44 PM)Jayaruh Wrote:
(03-18-2021, 01:14 PM)twhite Wrote: This might work better.

That looks like it might work with a NEW and a few others.

I was hoping with that design it will work with most razors. should work on the post type also. We will see.
This design also does not have the combs acting as a safety stop. So this is a fully exposed blade design.
Lost, If found do not return and do not feed.
The following 2 users Like twhite's post:
  • GAW9576, TobyC
Like Reply
#12
Awesome, just totally awesome!!!!
The following 1 user Likes Ordinaryshaver's post:
  • GAW9576
Like Reply
#13
(03-18-2021, 01:14 PM)twhite Wrote: This might work better.

Not that I'm an expert in unmentionable razors. Far from it. But wouldn't three holes be better?
Like in the original patent?
sɐǝɹpu∀ — https://razors.page @patents@razors.page
ᓚᘏᗢ


The following 1 user Likes riverrun's post:
  • GAW9576
Like Reply
#14
(03-18-2021, 06:11 PM)riverrun Wrote:
(03-18-2021, 01:14 PM)twhite Wrote: This might work better.

Not that I'm an expert in unmentionable razors. Far from it. But wouldn't three holes be better?
Like in the original patent?


Yes you are correct. I had fixed that this morning.


Attached Files Thumbnail(s)
   
Lost, If found do not return and do not feed.
The following 6 users Like twhite's post:
  • Droo78, GAW9576, Jayaruh, riverrun, TobyC, Tony'schin
Like Reply
#15
(03-18-2021, 06:34 PM)twhite Wrote:
(03-18-2021, 06:11 PM)riverrun Wrote: Not that I'm an expert in unmentionable razors. Far from it. But wouldn't three holes be better?
Like in the original patent?


Yes you are correct. I had fixed that this morning.

There you go. That looks just right.
Jim - The Cackalacky Kid "Finally, shaving is fun again..." 
The Jayaruh Brushes  - The Clan of Catchers
The following 3 users Like Jayaruh's post:
  • GAW9576, Tony'schin, twhite
Like Reply
#16
If you send it I'll test it. That looks cool. Tha angle the blade is held at makes it look like it would be good for shaving the back of my neck.
The following 3 users Like GAW9576's post:
  • Dave in KY, Tony'schin, twhite
Like Reply
#17
(03-18-2021, 11:34 PM)GAW9576 Wrote: If you send it I'll test it. That looks cool. Tha angle the blade is held at makes it look like it would be good for shaving the back of my neck.

Will do. I will be printing a few tomorrow so I will send one your way.
Lost, If found do not return and do not feed.
The following 4 users Like twhite's post:
  • Dave in KY, GAW9576, TobyC, Tony'schin
Like Reply
#18
Awesome. As always I look forward to trying another one of your creations.
The following 3 users Like GAW9576's post:
  • Jayaruh, Tony'schin, twhite
Like Reply
#19
Another nice looking creation, Tom! Can't wait to see how it works out.
~ Justin M.
The following 4 users Like mayer57619's post:
  • GAW9576, Jayaruh, Tony'schin, twhite
Like Reply
#20
Well it will work. But why?
I need to slot the holes so the cap will slide into place. I also need to make the blade stops wider. The holding design works quite well if I do say so.


Attached Files Thumbnail(s)
   
Lost, If found do not return and do not feed.
The following 6 users Like twhite's post:
  • Dave in KY, Droo78, GAW9576, ischiapp, Jayaruh, TobyC
Like Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)