Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
3D Print SE razor
#1
In TOST I've seen my first SE made by 3D print.
After that, I've been hooked.
Tongue

Thanks to twhite and riverrun, now I've the TNNIBR aka Wabbit.
[Image: CC8HsyQ.jpg]
[Image: o8TpFLYm.jpg][Image: ZwQKSPFm.jpg]

Recently I've found some nice threads about Thingiverse designers.
Here my favs.

https://www.thingiverse.com/thing:4646886
[Image: cBs4Rcc.jpg]

https://www.thingiverse.com/thing:4669389
[Image: Sp5V4WA.jpg]

https://www.thingiverse.com/thing:4667202
[Image: Mj4BE1S.jpg]
Where there is a great desire there can be no great difficulty - Machiavelli & Me
Greetings from Ischia. Pierpaolo
https://ischiapp.blogspot.com/
The following 11 users Like ischiapp's post:
  • bcshaves, Bryan_D, Droo78, GAW9576, Herm2502, Jayaruh, mayer57619, mlb 549, RobinK, srqshaver, twhite
Like Reply
#2
There really are some fun looking printed razors. Thanks for putting that together.
Happy shaves to ya!
The following 3 users Like Wchnu's post:
  • Droo78, GAW9576, ischiapp
Like Reply
#3
Photo 
Another clever design: EndGem Speed by Roger Quintero.
https://www.thingiverse.com/thing:4689575
[Image: Xd6FOJ9.jpg]
Where there is a great desire there can be no great difficulty - Machiavelli & Me
Greetings from Ischia. Pierpaolo
https://ischiapp.blogspot.com/
The following 9 users Like ischiapp's post:
  • bcshaves, Droo78, Flintstone, GAW9576, Jayaruh, mayer57619, mlb 549, srqshaver, twhite
Like Reply
#4
I am enjoying my Triceratops. You can use injector blades in it, too. Here is a video about changing the blade.

Jim - The Cackalacky Kid "Finally, shaving is fun again..." 
The Jayaruh Brushes  - The Clan of Catchers
The following 7 users Like Jayaruh's post:
  • Droo78, GAW9576, ischiapp, MaineYooper, mlb 549, srqshaver, twhite
Like Reply
#5
I've gone crazy I think for 3d printed razors. I am also making cases to house my 3d printed razors.
This is one of my latest razors: the GEM-LP (low profile).
[Image: IMG_3502.JPG]
I made this case for it today.
[Image: IMG_3526.JPG][Image: IMG_3522.JPG]

This is my Gem type razor in green resin.
[Image: IMG_3501.JPG]
And the case I made for it.
[Image: box44_03.jpg]

Here is my new red and black EndGem.
[Image: IMG_3503.JPG]
And its case.
[Image: box43_03.jpg]

I think you have already seen my gray and black EndGem.
[Image: IMG_3441.JPG]

Next week, I will be doing a 3d razor week. I will start it of with my first 3d printed razor, the TNNSER. I had a bunch of these, but I have gotten down to my black and green ones.
[Image: IMG_3143.JPG]

Too many razors, not enough time.
Jim - The Cackalacky Kid "Finally, shaving is fun again..." 
The Jayaruh Brushes  - The Clan of Catchers
The following 6 users Like Jayaruh's post:
  • bcshaves, GAW9576, ischiapp, mlb 549, riverrun, srqshaver
Like Reply
#6
I believe most of these are printed in ABS or PLA. Has anyone used PTEG? If how's the quality and durability so far?
Like Reply
#7
Photo 
After seeing Mr. White's twhite great little Fuzzy Catcher, I decided to revisit the possibilities of duplicating a couple of my favorite lather catchers for 3d printing. I was also curious about the big fuss with the baton handles on the GEM Juniors. Turns out I really like how the fat handle feels, especially on light razors. The pictures below are my final design, which is a combination of two lather catchers, and the blade holding method of the 3d printed WeckGem, but with more blade feel, and of course, a baton handle. I'm finalizing the geometry for easier printing and will make the files available soon.
   
   
   
   
   
The following 7 users Like SlimGem's post:
  • Dave in KY, GAW9576, ischiapp, Jayaruh, riverrun, srqshaver, Wchnu
Like Reply
#8
(05-01-2021, 08:17 PM)SlimGem Wrote: After seeing Mr. White's twhite great lithe Fuzzy Catcher, I decided to revisit the possibilities of duplicating a couple of my favorite lather catchers for 3d printing. I was also curious about the big fuss with the baton handles on the GEM Juniors. Turns out I really like how the fat handle feels, especially on light razors. The pictures below are my final design, which is a combination of two lather catchers, and the blade holding method of the 3d printed WeckGem, but with more blade feel, and of course, a baton handle. I'm finalizing the geometry for easier printing and will make the files available soon.
VERY COOL !!!
Viewer # 7  Musketeer #1
Running Amuck !
The following 2 users Like Dave in KY's post:
  • GAW9576, SlimGem
Like Reply
#9
Awesomelicious SlimGem
Happy shaves to ya!
The following 2 users Like Wchnu's post:
  • GAW9576, SlimGem
Like Reply
#10
JayaruhI've gone crazy I think for 3d printed razors. I am also making cases to house my 3d printed razors.
This is one of my latest razors: the GEM-LP (low profile).

I made this case for it today.


This is my Gem type razor in green resin.

And the case I made for it.


Here is my new red and black EndGem.

And its case.


I think you have already seen my gray and black EndGem.


Next week, I will be doing a 3d razor week. I will start it of with my first 3d printed razor, the TNNSER. I had a bunch of these, but I have gotten down to my black and green ones.


Too many razors, not enough time.

I missed this before. Beautiful collection there!!
Happy shaves to ya!
The following 2 users Like Wchnu's post:
  • Jayaruh, SlimGem
Like Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)